Open HardwareAssembly Instructions
Guides for installation and assembly of the LulzBot line of products made by FAME 3D LLC.
Guides for installation and assembly of the LulzBot line of products made by FAME 3D LLC.
1x [AS-TH0088] Twin Nebula 175 (0.5mm), LGX Assembly
1x [DC-LB0012] White 7 x 1/2 x 2 laser label
1x [DC-LB0160] Tool Head Serial Number Sticker, Matte Silver, 1" x 0.5", Thermal
1x [DC-LB0229] T.B.D. TWIN NEBULA 175 LABEL
1x [DC-MS0054] Firmware Update Warning Cards
1x [DC-MS0060] CONGRATULATIONS!- Accessory Instruction Card, V1.2
1x [EL-HR0230] Twin Nebula E0 Jumper
1x [EL-HR0231] Twin Nebula E1 Jumper Harness
4x [HD-BT0157] Class 12.9 Alloy Steel Black-Oxide SHCS, M3 x 8mm Length, 0.50mm Pitch
160mm [HD-TB0007] Feed Tube, 0.187" ID X .250" OD NAT PTFE Tube
1800mm [HD-TB0080] Feed Tube, 2mm ID X 4mm OD NAT PTFE Tube
2x [PP-GP0524] Feed Tube 175Converter_ProS/SideKick
1x [PP-GP0940] Tube Collar 2 1.75mm
1x [PP-GP0941] Tube Collar 1 1.75mm
1x [SH-PA0016] 8 X 8 Convoluted Foam 2 pc Set
1x [SH-PA0066] TAZ Pro, Tool Head Korrvu 8" x 8" x 6" Outer Box
2x [SH-PG0002] 3 x 4" 2 Mil Reclosable Polypropylene Bags
1x [SH-PG0003] 4 x 6" 2 Mil Reclosable Polypropylene Bags 1,000/carton
813mm [SH-PG0131] Custom Printed LulzBot White Tape
2x TAZ Pro Kit Label
1x Jumper Cables Label
2A) Cut two 80mm pieces of HD-TB0007 and grab 2x SH-PG0002, 2x PP-GP0524, 4x HD-BT0157, and 2x TAZ Pro label.
2B) Insert the tubes into the 2x PP-GP0524 and secure using 4x HD-BT0157. Be careful not to over tighten the screws.
2C) Put the TAZ Pro label on 1x SH-PG0002 and put the tube assembly in the bag.
2D) Grab 1x EL-HR0230, 1x EL-HR0231, 1x SH-PG0003, and 1x Jumper Cable label.
2E) Put the Jumper Cable label on SH-PG0003 and put EL-HR0230 and EL-HR0231 inside the bag.
2F) Cut two 900mm pieces of HD-TB0080. Put 1x PP-GP0940 on one tube and 1x PP-GP0941 on the other.
3A) Turn on the tape machine and the heater. The heater should be on for 20-30 minutes before using.
3B) Grab 1x SH-PA0066. Fold up the box and secure the bottom using a 16in. (Short Length if in Tool Heads) piece of tape.
3C) Clean up the corners of the box using a side cutter.
3D) Place the back label from DC-LB0229 on the back of the box and place the front label from DC-LB0229 on the front of the box. Note the box orientation.
3E) Place DC-LB0012 on the inside of the back flap of the box as shown.
3F) Place one half of SH-PA0016 in the box. Place 1x DC-MS0054 and 1x DC-MS0060 in the back of the box between the foam and box.
3G) Place the two tubes in the box.
3H) Place AS-TH0088 in the box.
3I) Place all three kit bags in the box.
3J) Place the other half of SH-PA0016 in the box. Close the box and secure using a 16in. (Short Length if in Tool Heads) piece of tape.
3K) Clean up the corners of the box using a side cutter.
3L) Place 1x DC-LB0160 on the front label where shown.
