Open HardwareAssembly Instructions
Guides for installation and assembly of the LulzBot line of products made by FAME 3D LLC.
Guides for installation and assembly of the LulzBot line of products made by FAME 3D LLC.
1x [AS-TH0085] Meteor 175 (0.5mm), LGX Ace Assembly
1x [DC-LB0012] White 7 x 1/2 x 2 laser label
1x [DC-LB0160] Tool Head Serial Number Sticker, Matte Silver, 1" x 0.5", Thermal
1x [DC-LB0226] Meteor 175 Tool Head Label, Front and Back 7 X 3
1x [DC-LB0231] Meteor 175 Tool Head Label, Back
1x [DC-MS0054] Firmware Update Warning Cards
1x [DC-MS0060] CONGRATULATIONS!- Accessory Instruction Card, V1.2
2x [HD-BT0157] Class 12.9 Alloy Steel Black-Oxide SHCS, M3 x 8mm Length, 0.50mm Pitch
1x [HD-MS0058] Wire Tie, 8" Black, pk 1000
80mm [HD-TB0007] Feed Tube, 0.187" ID X .250" OD NAT PTFE Tube
900mm [HD-TB0080] Feed Tube, 2mm ID X 4mm OD NAT PTFE Tube
1x [PP-GP0524] Feed Tube 175Converter_ProS/SideKick
1x [PP-GP0653] Feed Tube Spinner 2.85mm_TAZ SideKick
1x [SH-BX0080] 7 X 7 X 4 White Indestructo Box
1x [SH-PA0016] 8 X 8 Convoluted Foam 2 pc Set
2x [SH-PG0002] 3 x 4" 2 Mil Reclosable Polypropylene Bags
2x [SH-PG0129] Laser Labels - White, 1 1⁄2 x 1 1⁄2"
812.8mm [SH-PG0131] Custom Printed LulzBot White Tape
2A) Cut an 80mm piece of HD-TB0007 and grab 1x SH-PG0002, 1x PP-GP0524, 2x HD-BT0157, and 1x TAZ Pro label.
2B) Insert the tube into PP-GP0524 and secure using 2x HD-BT0157. Be careful not to over tighten the screws.
2C) Put the TAZ Pro label on 1x SH-PG0002 and put the tube assembly in the bag.
2D) Grab 1x SH-PG0002, 1x HD-MS0058, 1x PP-GP0653, and 1x Workhorse/SideKick label
2E) Put the Workhorse/Sidekick label on SH-PG002 and put HD-MS0058 and PP-GP0653 inside the bag
3A) Turn on the tape machine and the heater. The heater should be on for 20-30 minutes before using.
3B) Fold up SH-BX0080 and place DC-LB0012 where shown.
3C) Cut a 900mm piece of HD-TB0080. Place one half of SH-PA0016 in the box with the tube on top.
3D) Place AS-TH0085 and the two kits in the box.
3E) Place the other half of SH-PA0016 in the box with DC-MS0054 and DC-MS0060 on top and close up the box.
3F) With the heater warmed up, cut a 10in. (Long Length if in Tool Heads) piece of SH-PG0131 and place on each side of the box.
3G) Cut a 12in. piece of SH-PG0131 and place across the front of the box.
3H) Place DC-LB0231 on the back of the box.
3I) Place DC-LB0226 on the front of the box.
3J) Place DC-LB0160 on DC-LB0226 where shown.
