Project Dashboard KITTAZ KITTAZ and TAZ 5 Extruder Assembly Workflow

1 Gather tools and components for assembly

Components

  • Extruder Body A6
  • Extruder Idler with 608 bearing installed B21, B2
  • Extruder Washer A6
  • Large Herringbone Gear A6 with Hobbed Bolt B4
  • Small Herringbone Gear A6
  • Extruder Latch A6
  • Motor _Box D__
  • 608 Bearing B21
  • Extruder Spring B20
  • M3 x 6mm set screw B6
  • M3 x 12 SHCS B9
  • M3 x 25 SHCS B10
  • M3 Nut B5
  • M3 Washer B7
  • M4 x 55 SHCS with Thumb Screw Knob B12
  • M4 Nut B11
  • M4 Washer B11
  • M8 Nyloc Nut B17
  • M8 Washer B18
  • M8 Shim Washer 0.5mm B2
  • M8 Shim Washer 1.0mm B2

Tools

  • 1.5 mm Allen Driver
  • 2.5 mm Allen Driver
  • 13 mm Wrench
Tools

2 Install Idler bolt

Install M3 x 25 SHCS, M3 Washer and M3 Nut into the Idler assembly. Only put the screw in till the tip is flush with the nut.

Tip: Set M3 Nut into hexagon cutout and hold with your finger to install the bolt.

If needed, insert 8mm smooth rod into 608 bearing and press them into the idler block. This may require force. You can use a pair of pliers covered to prevent damaging the parts to snap in the 608 bearing and 8mm shaft.

Idler block

3 Install extruder washer into body

Place the printed extruder washer into the extruder body.

Components
Washer installed

4 Install gear, bolt and first bearing

If needed, press hobbed bolt into large herringbone gear.

Install 1x M8 washer onto hobbed bolt then a 608 bearing.

Once installed, does the hobbing on the bolt line up with the small hole going thru the extruder body?

If you need to adjust it's location, you can add either a 0.50mm or 1.0mm shim washer to get the correct spacing.

Gear, bolt, washers and bearings
Pushed in to check hobbing location

5 Install second bearing

On the opposite side of the gear, add a 608 bearing, M8 Washer and a M8 nyloc nut.

Tighten the Locknut down until the bearing is seated and there is no space between the Nut, Washer and Bearing.

You may need to go back and add or subtract a 1mm shim washer or .5mm shim washer.

The large gear shouldn't be able to rock back and fourth, but should spin freely.

Second bearing, washer, nut

6 Install Idler onto body

Install extruder idler onto the body.

Tighten the M3 x 25, SHCS bolt down to secure the Idler.

Tip: Place the leg with the nut on the body first and twist the Idler onto the body.

Idler installed

7 Small herringbone gear assembly

Install the M3 nut into the bottom of the small herringbone gear.

Then install the M3 x 6mm set screw through the side of the small gear and into the nut.

Be sure the M3 x 6mm set screw does not protrude into the hole through the small gear.

Install nut
Install set screw

8 Install gear on moto

Locate the flat side of the motor shaft.

With the set screw aligned with the flat, slide the small gear onto the motor shaft.

The location will be adjusted later so positioning isn't important at this point.

Do not tighten the set screw yet.

Small gear placed on motor shaft

9 Install motor

Holding the motor in the location where it will be mounted, align the herringbone gears by sliding the small gear in or out on the motor shaft so the V-grooves are centered on each other.

Install motor using 3x M3x12 SHCS and 3x M3 washers, taking note of the orientation of the motor wires.

Push the gears together while you tighten the bolts to make sure the contact is tight.

Tighten the set screw on the small herring bone gear.

There shouldn't be any backlash in the gears.

Bolt locations
Gear alignment

10 Install M4 nuts into top of the body

Install 2x M4 nuts into the top of the extruder body as shown.

Make sure you can see the nuts from the side so you can install bolts later.

Tip: Nuts only go in one way, the flats of the nut must be vertical.

View from top
View from side

11 Install Extruder Latch

Install M4x55 thumb screw, M4 washer, extruder spring, M4 washer and Extruder latch into M4 nut installed in body.

Then put another M4 x 55 with thumb knob, M4 washer, extruder spring, M4 washer through the Extruder latch and into the body.

Make sure extruder latch is oriented correctly.

Extruder latch
Attached

12 Review the Extruder Assembly

Review your assembly for workmanship.

Extruder complete
Done! Take me home