1x- [AS-PR0136] X-End Left Assembly, Taz Pro
1x- [AS-PR0130] X-End Right Assembly, Taz Pro
2x- [AS-PR0137] Spool Arm Assembly, Taz Pro
1x- [AS-PR0138] Y Chain Pivot Assembly, Taz Pro
1x- [AS-PR0150] T-Slot dust cover, cut, 285mm
1x- [AS-PR0151] T-Slot Dust cover, cut, 522mm
1x- [EL-HR0142] Z Endstop Harness, Assembled
1x- [PP-IS0097] Z-Chain Mount with Inserts, Taz Pro
4x- [PP-IS0098] Bed Mount Chassis with Insert, Taz Pro
2x- [HD-BT0049] SHCS, M5x14
72x- [HD-BT0073]BHCS M5x10
8x- [HD-BT0250] Flanged Hex Head Screw, M5x10
1x- [HD-BT0225] 316 Stainless Steel BHCS M5x10
4x- [HD-EX0062] T-Slot Aluminum Frame TPW, Extrusion 20mm x 20mm x 500mm,Tapped M5x0.8 on Both Ends, Black (Ends free of anodize)
4x- [HD-EX0086] T-Slot Extrusion, Aluminum, 20mm x 20mm, 20.866" 530m
8x- [HD-EX0090] 90 degree Corner Bracket 2 Hole 20mm Slotted Inside Corner Bracket with Dual Support for 20 Series
1x- [HD-EX0092] 2 Hole Inside Corner Bracket For 20 Series
3x- [HD-NT0044] Post assembly M5 T-nut
73x- [HD-NT0053] T-Slot Slide in T-nuts for Aluminum Frame, M5
1x- [HD-WA0007] M5 Washer Zinc
74x- [HD-WA0040] M5 Washer
8x- [PP-FP0152] Corner Bracket
4x- [PP-GP0409] Frame Foot, Taz Pro
1x- [PP-GP0410] Electronic Chassis Mount-Front, Taz Pro
2x- [PP-GP0411] Electronic Chassis Mount-Back, Taz Pro
Using two [HD-BT0073] M5x10 BHCS and two [HD-WA0040] M5 black oxide washers, fasten the [PP-GP0409] frame feet to the threaded holes in the bottom of the frame assembly.
Using one [HD-BT0049] M5x14 SHCS and one [HD-WA0040] M5 black oxide washer, fasten the [AS-PR0137] spool arm assembly to the post assembly nut on the photo left side of the frame. This can be left loose at this time.
Using one [HD-BT0073] M5x10 BHCS and one [HD-WA0040] M5 black oxide washer, fasten the [PP-GP0410] front electronics chassis mount to bottom most t-slot nut on the photo right side of the frame.
Using one [HD-BT0225] M5x10 stainless steel BHCS and one [HD-WA0007] M5 stainless washer, fasten the [HD-EX0092] aluminum corner bracket to the top most t-slot nut on the photo right side of the frame.
Using two [HD-BT0073] M5 x 10 BHCS and two [HD-WA0040] M5 washer, attach the [PP-GP0411] back chassis mount to the frame.
Use two [HD-BT0073] M5 x 10 BHCS and two [HD-WA0040] M5 washer, attach the [PP-IS0098] Y-Mount Chassis to the frame. Make sure to have one t-nut to the left of the chassis mounts.
Flip the frame so the corner brackets are facing up. Use three [HD-BT0073] M5 x 10 BHCS and three [HD-WA0040] M5 washer, attach the z-cable chain mount to the frame. Use the spacing jig to set the height.
Use one [HD-BT0049] M5 x 14 SHCS and one [HD-WA0040] M5 washer, attach the spool are to rear frame. USe sapcing jig to set the height.
Take the [EL-HR0142] and place it into the frame extrusions as shown. Use the [AS-PR0150] 285mm dust cover and cover the wires on the left side of the frame. Use the [PR0151] 522mm dust cover and cover the wires on the top of the frame.
Take the front frame piece and lay it so the bottom of the frame is towards the top.
Take the z-motor assembly [AS-PR0136] and place it on the frame as shown.
Using two [HD-BT0073] M5 x 10 BHCS and two [HD-WA0040] M5 washer, screw the z-upper to the frame as shown. Use two M5x10 Flanged Hex Head [HD-BT0250] to attach the z-lower to the frame.
Take the assembled back frame and place it onto the x-ends as shown. Do not pich the wires for the z-max switches when sliding the back frame onto the x-ends.
Use four [HD-BT0073] M5 x 10 BHCS and four [HD-WA0040] M5 washers, and attach the z-uppers to the frame.
Flip the frame over so the screw holes for the z-lowers are facing you.
Use four [HD-BT0250] M5 x 10 Flanged Hex Head to secure the z-lowers to the frame.
The 4 frame feet must be removed for this step
Take the frame to the granite block and check the squareness of the frame. Use a 12" rafter square to check the frame for squareness. The frame must be within 2mm of the rafter scale on either the top or bottom of the square.
Torque all 8 Z-Lower to Frame fasteners [HD-BT0250] to 15in*lbs
There are no loose or un-torqued screws.
Both spool arms are attached.
Z-cable chain mount is attached.
All four y-chassis mounts are attached and in the correct place with the spacing jig.
Y-chain pivot assembly is attached and up against the frame corner.
Z-max wires are plugged in and going to correct terminals.
All four feet are attached.